Call us : +33 2 33 61 16 70

STHC - Modbus RS485 combined probe

Reference GSTHC102R

Sensor temperature, relative humidity and CO 2 - STHC 102 is designed to measure carbon dioxide concentration, temperature and relative humidity in areas protected from water.

1.26MB Download

Datasheet GSTHC102R | Combined probe STHC - Modbus RS485

Product features STHC - Modbus RS485 combined probe

Room sensor

Sensor temperature, relative humidity and CO 2 - STHC 102 consists of a plastic head with grooves in which there is a printed circuit board with individual sensors and transmitter to ensure communication via an RS 485 bus. The temperature and relative humidity are measured by a common internal sensor it is processed in the microprocessor and converted into a MODBUS RTU output signal. The CO value 2 is measured by the NDIR module, the digital signal of which is also converted into a MODBUS RTU output signal. A function of self-calibration is available for the CO concentration sensor 2 , which ensures that the sensor is set to a minimum CO value 2 corresponding to the level of external concentration. Temperature, relative humidity and CO sensor 2- STHC 102 conforms to protection class IP 30 according to EN 60529Le sensor temperature, relative humidity and CO 2 STHC 102 recommended is located at a height of 1,5 m from the interior wall, in the area of ​​movement of people, away from sunny places and places affected by the temperature of the walls, heat sources or lighting.

Sensor temperature, relative humidity and CO 2 - STHC 102 is designed to operate in a chemically non-aggressive environment. Operating conditions to ensure the proper functioning of the CO sensor 2 are the following:

  • ambient temperature: 0 to 45 ° C
  • relative humidity: 0 to 85% (non-condensing)
  • atmospheric pressure: 87 to 106 kPa 

Sensor type STHC 102
Temperature measurement range ** 0 to 45 ° C with guaranteed accuracy of CO measurement 2
-30 to 70 ° C without guaranteed accuracy of CO measurement 2
Temperature measurement accuracy * ± 0,5 ° C
Relative humidity measurement range * 0 to 85% with CO measurement accuracy 2 guarantee 
0 to 95% without CO measurement accuracy 2 guarantee
Relative humidity measurement accuracy * ± 3% in the range of 10 to 85% 
± 4,5% in the range of 0 to 10%
CO measurement range 2 * 400 to 5000 ppm
CO measurement accuracy 2 * ± 100 ppm
CO reaction time 2 (90%) 90 s
Output signal RS485 / MODBUS RTU
Supply voltage 15 to 30 V DC
Nominal supply voltage U n 24 V DC
The consumption max: 500mW 
typical: 300 mW
Degree of protection IP 30 according to EN 60529
Head dimensions 71,9 x 59 x 27 mm
Head material lexan
The weight min 35g
Recommended conductor cross-section 0,14 to 1 mm 2

The manufacturer reserves the right to modify the design and technical characteristics of the products.

The sensors are designed to be mounted on a wall or other vertical surface. For fixing, it is necessary to prepare the required holes for mounting screws using a template (supplied with the sensor).
Before connecting the power cable, it is necessary to separate the perforated cover from the plastic base. Remove the cover and insert the cable through the 9 mm hole, apply the base to the surface and screw with two screws or bolts. The length of the bolts or fixing screws for fixing should be chosen according to the thickness of the plastic base. Connect the power cable to the terminals in accordance with the “Wiring” section. Diagram: place the perforated cover on the fixed base and lock it by clicking on it. After installation and connection to the electrical measuring device, the sensor is ready for use. The sensor does not require any particular maintenance.

These products can interest you

CO2 probe - CAN protocol

STHCPV Combined Probe - CAN

Combined indoor sensor for temperature, relative humidity, CO 2, atmospheric pressure and VOC - STHCPV 104 is c ...