
Wired temperature and humidity sensor with digital output
Reference: AR003928

International shipping
Standard or express delivery
Secure Payments
All payments are secure and approved.
Best price guarantee
Contact us to define your payment method.
+33-233-611-670
English - French - German - Spanish
Product details about "Wired temperature and humidity sensor with digital output"
Recommended operating conditions to ensure the most accurate output values:
- ambient temperature around the sensor: 5 to 60 ° C
- relative ambient humidity: 20 to 80%
- atmospheric pressure: 87 to 106 kPa
The temperature and relative humidity sensor is protected by a special PTFE membrane, which increases the resistance of the sensor against the impact of dust and water, ensures the minimum level of protection IP 65 according to EN 60759. as 'amended and allows the sensor to be used in severe conditions with a greater occurrence of dust or water spray.
The temperature and relative humidity sensors are designed to operate in chemically non-aggressive environments; their mode of use must be chosen according to the temperature and the chemical resistance of the case and the power cable.
Warnings and Restrictions - Sensors should not be used to measure the temperature in areas:
- Or the specified technical parameters and operating conditions are not met
- Possible mechanical impact on the sensor
- Explosion risk area
- Chemically aggressive environment
- where the sensor could be exposed to permanent immersion in a liquid
- where the sensor could be exposed to the impact of electrostatic discharge (ESD)
Failure to comply with the stated recommendations and long-term exposure to conditions outside the recommended operating conditions will have a negative impact on the measurement accuracy and the service life of the temperature sensor. Especially at high humidity, there may be an offset of the RH output signal (for example, + 3% RH after 60 hours kept above the value of 80% RH). When the standard temperature and humidity range is restored, the sensor automatically returns to the calibrated state.
ACCESSORIES:
- different connector variants --- HIRSCHMANN, LEMO, MOLEX, JST, etc.
DECLARATION, CERTIFICATION, CALIBRATION
The manufacturer issues an EU declaration of conformity.
Sensor type
|
GTH161R |
Type of detection element T + RH
|
SHT30F |
Bus communication
|
I2C, maximum communication speed 1 MHz |
Temperature measurement range
|
maximum: -20 to 80 ° C |
Temperature measurement accuracy
|
± 0,2 ° C in the range of 0 to 65 ° C |
Relative humidity measurement range
|
maximum: 0 to 100% |
Relative humidity measurement accuracy
|
± 2% in the range of 10 to 90% |
Vdd power supply
|
2,15 to 5,5 V |
Protection sign
|
IP 65 according to EN 60529, as modified |
Response in time (25 ° C, 1 m / s) *
|
temperature: the response time is influenced by the design of the sensor housing and the position of the sensor in a specific application τ0,63> 2 s |
Housing
|
polyamide-based plastic - THERMELT 867 |
Case diameter
|
8 ± 0.1 mm |
Case length
|
40 mm |
Power cable type
|
Unshielded PVC 5 x AWG 28, diameter 4,0 ± 0,3 mm |
Power cable length
|
max 3m |
Weight
|
30 g for 1m of cable |
General
- Reference AR003928
- Name Wired temperature and humidity sensor with digital output
- In stock 8 products
Features
- Measured Humidity
- Product Type Wired probes
8 other products in the same category:


SHT20 / SHT21 Temperature and Humidity Sensor
- ambience
- Exit 485 / 232
- Sensor of your choice
- Custom cable

MiniDIN digital temperature and humidity probe

Digital temperature / humidity probe for WebSensor with CINCH connector

DIGIL / M digital temperature / humidity probe, MiniDin connector

DIGIL / E digital temperature / humidity probe, ELKA connector

Digital temperature and humidity probe ELKA connector

Plastic housing temperature and humidity sensor
- ambience
- Exit 485 / 232
- Sensor of your choice
- Custom cable