Outdoor sensor - Plastic connection box *Step required

GNS110R
In production :  3 to 5 weeks
Description and application
These resistance temperature sensors are intended for measuring the contact temperature of gaseous substances. The plastic connection head is supplied with a cable outlet ring (the terminal block is located in the head) or a connector. The standard temperature range of use of the sensors is between -50 and + 100 ° C. The temperature sensors can be used for any control system compatible with the output signals of the sensing elements or the output signals shown in the table of sensing element types. The temperature sensor is easy to mount thanks to the unique "S-head" design.

The temperature sensors are designed to operate in a chemically non-aggressive environment.

Unit price
32,67 €
Final price
32,67 €
Your configuration:

International shipping

FREE shipping in Europe from 100 € of purchase

Secure Payments

All payments are secure and approved.

Best price guarantee

Contact us to define your payment term.

+33-233-611-670

English - French - German - Spanish

Outdoor sensor
6-195.jpg
Room sensor

ACCESSORIES

  • CONEC 43-00092 input connector
  • connection cable with straight type RKT connector or with rectangular type RKWT connector

DECLARATION, CERTIFICATION, CALIBRATION

  • The manufacturer provides an EU declaration of conformity.
  • Calibration - The final metrological control - comparison with standards or working instruments - is carried out for all products. The continuity of standards and work measurement instruments is ensured within the meaning of article 5 of Law No. 505/1990 on metrology. The manufacturer offers the possibility of supplying the calibrated sensors in the laboratory (according to the requirements of EN ISO / IEC 17025) or in an accredited laboratory.  

Attention: 4-20 mA output temperature sensors can be delivered with the new connection head only in version A.

Sensor type 
(K - with connector)
NS 110x 
NS 110xK
NS 111x
NS 111xK
NS 112x
NS 112xK
NS 310x
NS 310xK
NS 311x
NS 311xK
Sensitive element type
Ni 1000/5000 Ni 1000/6180 Ni 891 Ni 10000/5000 Ni 10000/6180
Measuring range
-50 to 100 ° C
Current continuous from maximum measurement

1 mA 1 mA 1 mA 0.3 mA 0.3 mA

Sensor type 
(K - with connector)
NS 113x
NS 113xK
PTS 110x 
PTS 110xK
PTS 210x 
PTS 210xK
PTS 310x 
PTS 310xK
HS 110x 
HS 110xK
Sensitive element type T1 = Ni 226 PT 100/3850 PT 500/3850 PT 1000/3850 20 kΩ NTC thermistor
Measuring range -50 to 100 ° C
Current 
continuous from maximum measurement
0.7 mA 3 mA 1.5 mA 1 mA 0,3 mW *)

*) maximum power consumption

Sensor type 
(K - with connector)
NS 510A
NS 510AK
NS 710x 
NS 710xK
Notes
Sensitive element type Pt 1000/3850 PT1000 / 3850
Output signal
4 to 20 mA 0 to 10 V
Measure the edges
-30 to 60 ° C 
0 to 35 ° C 
0 to 100 ° C 
0 to 150 ° C
-30 to 60 ° C 
0 to 35 ° C 
0 to 100 ° C 
0 to 150 ° C
Ambient temperature around the connection -30 to 70 ° C
Power supply (U) 11 to 30 V DC 15 to 30 V DC Recommended value 24 V DC
Resistance to load Rz 150 Ω for 12 VDC power supply 
700 Ω for 24 VDC power supply
> 10kΩ
Output signal 
- braek sensitive elements
> 24 mA > 10.5 mA
Output signal 
- short sensitive element
<3.5 mA ~ 0 V

Note: x = version A or version B

**) Depending on customer requirements, it is possible to provide a custom measurement range from -40 to 150 ° C; the minimum range of the range must be 35 ° C (for example, -20 to 15 ° C; -30 to 80 ° C)

OTHER PARAMETERS
Precision class
Sensitive elements Ni: class B, t = ± (0,4 + 0,007 t), for t ≥ 0; t = ± (0,4 + 0,028 | t |), for t ≤ 0 in ° C; 
Elements sensitive to pt: class B according to EN 60751, t = ± (0.3 + 0.005 | t |) in ° C 
NTC 20 kΩ: ± 1 ° C for the range from 0 to 70 ° C
Measurement error 
NS 510A (K), NS 710x (K)
NS 510A ± 1 ° C (depending on the air flow speed) 
NS 710A 0,6% for the range with span; min. 0,5 ° C
Connection of sensors
according to the wiring diagram
Standard rod length (version A) for resistance output and for 0 to 10 V output: 25 mm 
for 4 to 20 mA output: 50 mm
Response time
τ 0,5 <9 s (air flow at 1m s -1 ) - version A 
τ 0,5 ≤ 30 s (air flow at 1m s -1 ) - version B
Recommended wire section 
- sensors with grommet
0,35 to 1,5 mm 2
Connector type in the head 
- sensor with connector
RSFM4 - Lumberg
Isolation resistance
> 200 MOhm at 500 V DC, 25 ° ± 3 ° C; humidity <85%
Ingress protection IP 65 according to EN 60529
Material of the stem
stainless steel DIN 1.4301 - version A
Connection head material
POLYAMIDE
Operating conditions
ambient temperature: -50 to 100 ° C; -30 to 70 ° C with a converter
relative humidity: max. 100% (at room temperature 25 ° C)
atmospheric pressure: 70 to 107 kPa
Weight about 0,15 kg



SENSOR INSTALLATION AND MAINTENANCE 

WELL DETECTORS:
Before connecting the power cable, lift the cover of the plastic connection head using a flat screwdriver. The input cable is connected to the terminals according to the wiring diagram through the loose eyelet. The recommended wire section is 0,35 to 1,5 mm2. The diameter of the circular section cable can range from 4 to 8 mm. To ensure the IP 65 protection value, the grommet must be tight and the cover must be put on after connecting the input cable.

SENSORS WITH CONNECTOR:
The input cable with connector is connected to the RSFM4 connector, which is part of the sensor head. Optionally the stand-alone CONEC 43-00092 connector, or an input cable with a length of 5 m, equipped with a straight type RKT connector or a rectangular type RKWT connector can be delivered. To ensure the protection value IP 65, the connectors and the sensor cover must be tightened and checked. In the event that the input cable is laid near high voltage conductors or those supplying equipment that create an interfering electromagnetic field (for example, inductive cables).
charge the equipment), a shielded cable should be used. The openings for the installation of the plastic clamp must be drilled in accordance with the sketch dimensions on which the opening diameters and the distances from their centers are illustrated. After installation and connection of the sensor to the sequential system assess the electrical equipment that the sensor is ready to use. The sensor does not require any particular maintenance. The device can be used in any working position, but the eyelet must not point upwards. The sensors are mounted using two methods: a) directly on the flat surface using two Ø 4,5 mm screws in the openings in the corners of the head. The dimension 13 mm (distance to the barrier in the head connection) must be added to the length necessary for attachment to a base; b) by means of the lateral support which must be fixed for example to a wall by means of two Ø 4,5 mm screws. To ensure watertightness, it is necessary to carefully tighten the eyelet. During the closing of the head by means of the cover the clips must be broken in the original position.

MODIFICATION AND CUSTOMIZATION FOR THE STANDARD DETECTORS MANUFACTURED, THE FOLLOWING PARAMETERS CAN BE MODIFIED:

- possibility of coating two sensitive elements.
- possibility of encapsulating non-standard temperature sensors (DALLAS, TSic, KTY, SMT, etc.).
- Accuracy class A (with the exception of Ni 10000/5000, Ni 10000/6180, T1 = Ni 2226 sensors, NTC resistance 20 kΩ).
- connection option with three or four wires.
- possibility of providing custom temperature ranges for temperature sensors with converter.

Information

Measured
Temperature
Product Type
Head / terminal probes
Communication
0 ... 10V
4 ... 20mA
Related products (8 other products in the same category)

Air or gas temperature sensor

Air or gas temperature probe response time less than a second probe temperature range -75 to ...
Price 18,24 €
5 products In stock

Create account