Call us : +33 2 33 61 16 70
EN
croatian Czech Dutch French German Italian polish Portuguese Romanian Spanish
Outdoor sensor - Metal connection head
Outdoor sensor - Metal connection head
Outdoor sensor - Metal connection head Outdoor sensor - Metal connection head

Outside temperature probe with metal head

Description and application
These resistance temperature sensors are intended for measuring the contact temperature of gaseous substances. The standard temperature range in which the sensors can be used is between -30 ° C and 100 ° C. The sensors can be used for any control system compatible with the output signals of the sensing elements or the output signals shown in the table of sensing element types.

The temperature sensors are designed to operate in a chemically non-aggressive environment.

Product features Outside temperature probe with metal head

Outdoor temperature sensor

ACCESSORIES
  • central metal support K110

DECLARATION, CERTIFICATES, CALIBRATION

  • The manufacturer provides an EU declaration of conformity.
  • Calibration - The final metrological control - comparison with standards or working instruments - is carried out for all products. The continuity of standards and work measurement instruments is ensured within the meaning of article 5 of the law. n ° 505/1990 on metrology. The manufacturer offers the possibility of supplying the calibrated sensors in the laboratory (according to the requirements of EN ISO / IEC 17025) or in an accredited laboratory.
  • Features
  • Cable schematics
  • Dimensional draft
  • Download
Sensor type NK-510 Footnotes
Sensitive element type Point 1000/3850
Trip 4 to 20 mA
Standard measuring ranges
 -30 to 60 ° C 
0 to 35 ° C 
0 to 100 ° C 
0 to 150 ° C		 ambient temperature around the connection head -30 to 70 ° C
Measurement error ± 1 ° C depending on the air flow speed
Voltage supply 
(U)		 11 to 30 V DC recommended value 24 V DC
Resistance to load Rz 150 Ω for 12 VDC power supply 
700 Ω for 24 VDC power supply
Output signal 
- failure of detection elements		 > 24 mA
Output signal 
- short circuit of the detection element
 <3.5 mA

OTHER PARAMETERS
Precision class
 Sensitive elements Ni: class B, t = ± (0,4 + 0,007 t), for t ≥ 0; t = ± (0,4 + 0,028 | t |), for t ≤ 0 in ° C; 
Elements sensitive to pt: class B according to EN 60751, t = ± (0.3 + 0.005 | t |) in ° C 
NTC 20 kΩ: ± 1 ° C for the range from 0 to 70 ° C
Connection of sensors
 according to the wiring diagram
Standard rod length 
 for resistance output: 25 mm 
for 4 to 20 mA output: 50 mm
Response time
 τ0,5 <9 s (in an air flow at 1 ms -1 )
Recommended wire section
 0,35 to 1,5 mm 2
Isolation resistance
 > 200 MOhm at 500 V DC, 25 ° ± 3 ° C; humidity <85%
Ingress protection IP 54 according to EN 60529
Material of the stem
 DIN 1.4301 stainless steel
Connection head type LIMATHER MA
Connection head material
 aluminum alloy
Operating conditions
 ambient temperature: -30 to 100 ° C; -30 to 70 ° C with a converter
relative humidity: max. 100% (at room temperature 25 ° C)
atmospheric pressure: 70 to 107 kPa
Weight about 0,2 kg


Please note: le manufacturer reserves the right to modify the design and technical characteristics of the products. For real information, please always contact your dealer.

SENSOR INSTALLATION AND MAINTENANCE

Before connecting the input cable, unscrew the metal connection head cover. The input cable is then connected to the corresponding terminals in the loose grommet according to the wiring diagram. Recommended wire section: 0,35 to 1,5 mm2, the outer diameter of the circular cable section can be 4 to 8 mm.

If the input cable is laid near high voltage conductors or those supplying equipment creating a disturbing electromagnetic field (e.g. equipment with inductive load), shielded cable should be used. To ensure IP 54 ingress protection, the grommet must be tightened and the cover screwed on after connecting the inlet cable.

The openings for the installation of the stainless steel brackets are drilled according to the dimensional draft, where the hole diameters and the distances between the hole centers can be found.

After installing and connecting the sensor to the appropriate electrical equipment, the sensor is ready for use. The sensor does not require any special servicing or maintenance. The sensors can be placed in any operating position, but the grommet must not be pointing upwards.

MODIFICATION AND CUSTOMIZATION

FOR MANUFACTURED STANDARD DETECTORS, THE FOLLOWING PARAMETERS CAN BE CHANGED:

  • possibility of coating two sensitive elements
  • possibility to encapsulate non-standard temperature sensors (DALLAS, TSic, KTY, SMT, etc.)
  • Accumulation class A (except sensors Ni 10000/5000, Ni 10000/6180, T1 = Ni 2226, NTC resistor 20 kΩ)
  • three or four wire connection option

These products can interest you